81 Nos of List Use Construction Tools and Pieces of Equipment

Civil Engineering Tools and Equipment

Construction tools list for building construction works such as concrete, brick masonry, leveling, woodworks, floor works, slab works, bricklaying, plastering, etc. is provided.

Every construction tool is necessary to achieve good results in the whole project.

List of Construction Tools and Pieces of Equipment

Here we are show

Sr.No.	Name of Material / Product	Use / Application
1.	Backhoe	To excavate the earth up to 3m depth.
2.	Binding Hook	To tie the binding wire in reinforcement.
3.	Block Plane (Wooden)	This tool is used in Door and window wood works.
4.	Bolster	Bolster is like chisel but it is used to cut bricks. Its cutting edge is wider than the width of brick. It is useful for accurate cutting of bricks.
5.	Boning Rod	Boning rods are made of wood and they are T shape. They are used to level the excavated trench throughout its length. Minimum three boning rods are used to level the trench surface.
6.	Brick Hammer	Brick hammer is used to cut the bricks and also used to push the bricks if they come out of the course line.
7.	Bulldozer	A bulldozer is a crawle with a substantial metal plate used fitted to push large amounts of soil, sand, dirt or other materials when construction or remodeling and usually push on the back with a claw mechanism to loosen densely-compacted materials.
8.	Bump Cutter / Screed	This tool is used to level fresh concrete surface especially in slab concrete.
9.	Chisel	To remove the settled mortar from the floor.

Sr.No.	Name of Material / Product	Use / Application
10.	Circular Saw	To cut the Steel rods and wood materials.
11.	Concrete Mixer Trucks	To transport the RMC from plant to site.
12.	Cordless Drill	This tool is used to make pilot holes, replacing jumper (special type of drill should be used while drilling concrete).
13.	Core Cutter Machine	To cut the concrete at particular diameter.
14.	Crow Bar	To remove the nails from shuttering board.
15.	De-Watering Pump	To de-water the seepage water.
16.	Digging Bar	To dig & loose the soil.
17.	Dozer	To level the earth surface.
18.	Drilling Machine	To make a hole in steel or wooden surface.
19.	Dumpers	A dump truck is a vehicle designed to transport bulk material, often in construction. It has a open jump ahead with the driver seat , and consist of a large boxlike body to contain materials. A dumper usually has 4 Wheels, where the entire load and the movement depends on.

Sr.No.	Name of Material / Product	Use / Application
20.	Earth Rammer	To compact the earth surface.
21.	End Frames	Their use is similar to the line and pins. But instead of pins, L shaped frames are used at the end of thread which hold the brick work effectively and level the alignment accurately.
22.	Excavator	To excavate the earth up to 5m depth.
23.	Forklift	To lift and transport materials.
24.	Framing Hammer	This tool is used to drive and remove nails.
25.	Framing Square	This tool is used in Brickwork, Plastering to check right angle.
26.	Gloves	Avoiding to direct contact with dangerous material or machinery.
27.	Grader	A grader is a construction machine with a long blade used to create a flat surface. It is commonly called in names such as road grader, a blade, a maintainer and motor grader,Graders are mostly been used in road construction for construction and maintenance of dirt roads and gravel roads.
28.	Hammer	To insert the nails into the board or wall.
29.	Hand Drill	This tool is used in hole in any material

Sr.No.	Name of Material / Product	Use / Application
30.	Hand Saw	This tool is used in wood works and shuttering.
31.	Hand Vibrator	This vibrator use small area vibrtion like column and beam.
32.	Head Pan	To transport the material.
33.	Helmet	The safety helmet should be necessary in construction works. Any material or structure may fall from height during construction work. So, to protect the head from injury or any fatal accident, this safety helmet should be used.
34.	Hoe	To excavate the earth or to dig a trench.
35.	Hoist	Hoist use of tie material and other normal woark.
36.	Hoist lift	Hoist is a device for raising or lowering a load by means of a drum or wheel lift to which wraps the rope or chain. It can be operated by hand, is driven electrically or pneumatically, and the chain or wire rope fibers are used as lifting device.
37.	Hydra Crane	To Lift the heavyweight items.
38.	Scoop	This use in QC department for material
39.	Jack Hammer	To break stone or concrete.

Sr.No.	Name of Material / Product	Use / Application
40.	Jack Plane(M.S.)	Jack plane is used in the wood work to smoothen the surface of doors and windows etc.
41.	Ladder	Ladder is also required in construction works. To check slab work, to transport material to the higher floors, to paint the walls etc.
42.	Line and Pins	Line and pins consists a thread whose ends are connected with two solid metal rods with pin points. It is used to level the alignment of brick course while brick laying.
43.	Line Level	This tool is used to check horizontal level in brickwork, plastering , flooring and tile works.
44.	Mason’s Square	Mason’s square is used to achieve perfect right angle at the corner of masonry wall. It is “L” shape. First course is laid properly using Mason’s square then based on the first, remaining layers of bricks are set out.
45.	Masonry Trowel	This tool is used to place cement mortar.
46.	Measurement Tape	To measure the length.
47.	Measuring Box	To measure the exact quantity while mixing the concrete or mortar.
48.	Measuring Wheel	To measure the length.
49.	Mixer Machine	To mix the material for preparing the concrete.

Sr.No.	Name of Material / Product	Use / Application
50.	Needle Vibrator	To level and settle the fresh concrete while pouring the concrete into reinforcement.
51.	Pick Axe	Pick axe is used to excavate the soil. It is more suitable for hard soil which is quite difficult to dig with spade or hoe.
52.	Pile Driller Machine	To dig the earth at deep.
53.	Plate Vibrator	This tool is used to vibrate the concrete in a thin section like slab while pouring. For workability purpose, we all add water to concrete. To avoid that we are using vibrators.
54.	Plumb Rule	Plumb rule is used to check the vertical line of wall whether it is perfect vertical or not. It contains a straight wood board with uniform edges. On its center a groove is provided in which plumb bob is situated. When the rule is placed vertically with the wall the plumb bob should be in the groove line otherwise the wall will not be vertical.
55.	Plumb Bob	Using to check the surface vertical alignment.
56.	Polisher	This tool is used to smoothen the surface (wood or marble flooring).
57.	Putty Knife	Putty knife is used level the putty finishing and also used to reduce the thickness of finish when it is more thick.
58.	Wier Brush	This use cleaning of any material.
59.	Rebound Hammer	To check the Compressive strength of concrete at Site.

Sr.No.	Name of Material / Product	Use / Application
60.	Wooden Float	To provide even surface while plastering
61.	Road Header Machine	A road header machine called a boom type road header. Road headers are advanced, self forced and extremely powerful rock cutting machines are designed to excavate roadways, tunnels and compartments continuously without using volatile. Powered electro hydraulically, they produce no fumes and are used extensively in mineral mining.
62.	Road Roller	To compact the earth.
63.	Rubber Boots	Avoiding direct contact with dangerous materials or machinery.
64.	Safety Belt	Should wear while doing work at heights.
65.	Safety Googles	Avoiding direct contact with dangerous materials.
66.	Sand Screening Machine	To sieve the sand.
67.	Scratchers	Plastering of a surface is carried out layer wise. Minimum 2 coats are necessary for plastering. To provide the good bond between the coats, bottom layer is scratched with a tool called scratchers.
68.	Skid Steer Loaders	A skid loader or skid-steer loader is a small rigid frame, engine-powered machine with lift arms used to attach a wide variety of labor-saving tools or attachments.Though occasionally they are equipped with tracks, skid-steer loaders are typically four-wheel vehicles with the wheels mechanically locked in synchronization on each side, and the left-side drive wheels can be driven independently of the right-side drive wheels.
69.	Wheel Barrow	To transport the materials inside the site.

Sr.No.	Name of Material / Product	Use / Application
70.	Spade	To excavate the earth or to dig a trench.
71.	Sprit Level	To check the horizontal surface level.
72.	Straight Edge Brushes	Straight edge brushes are used to provide finishing to the plastered surface especially at corners and edges of walls.
73.	Tile Cutter	To cut the tiles at the right size.
74.	Tower Crane	This crane use of material transport one building to another building in air.
75.	Trenchers Cutter	HomeMachinery And EquipmentUse of Trenchers in construction advantage and disadvantages Use of Trenchers in construction advantage and disadvantages admin May 20, 2015 Machinery and Equipment No Comments It is sometimes called as Ditchers or Trenches, are similar to excavators in the sense that penetrate the soil, break soil and rock, and from the earth. . They differ from excavators in that the soil is removed in one continuous movement. Digging trenches for pipes used specifically for, but other machines have been improvised in the past in order to serve this purpose.

Sr.No.	Name of Material / Product	Use / Application
76.	Trowel (Hand)	Used in masonry and plastering works to place the mortar.
77.	Vacuum Blower	To clean the dust from the floor.
78.	Water Level	To mark the spot level.
79.	Water Tanker	This use of storage of water specific location.
80.	Wedge	Wedge is a small hard metal blade which is used to cut the rock surfaces with the help of sledge hammer.
81.	Welding Machine Set	To joint the different pieces of steel.

Civil Engineering Tools and Equipment

List of Construction Tools and Pieces of Equipment

Leave a Reply Cancel reply